我在天马彩票平台输了三十万

Questions tagged [serial-port]

我在天马彩票平台输了三十万 A hardware interface commonly found on older PCs, usually with a 9-pin DE-9 socket/plug, on networking devices or servers also with RJ-45 socket/plug (otherwise commonly used for ethernet), or with a (much wider) 25-pin DB-25 socket/plug. Two common standards used with such an interface are RS-232 or RS-422.

Filter by
Sorted by
Tagged with
0
votes
1answer
21 views

Serial connection to radio using WINE

I can run the software for my CRT SS 9900 radio using the mfrs serial-to-USB cable under WINE on Zorin/Ubuntu. However, I cannot connect on any of the COM ports. I have set /ttyUSB0 using minicom but ...
2
votes
3answers
241 views

Simulating an input from ttyS0 in Linux

I work with cash registers that are bare-boned RedHat Linux boxes. These registers have a scanner attached to a serial port (ttyS0). We do a lot of testing that requires someone to stand at the ...
2
votes
1answer
35 views

Does Linux 'lose' serial/USB port numeration?

I have a machine (Debian/Ubuntu/CentOS mostly) that works like a kiosk, and there a few devices connected to it, using serial and USB ports. The software of these devices should know the port numbers, ...
1
vote
1answer
45 views

How to send and receive data from serial port using command line?

In the past, I have used c++ and python to communicate with serial ports in a Linux and Windows environment. In Linux, I have also used programs like picocom, minicom, and cutecom for serial ...
0
votes
0answers
25 views

Does IRCOMM work in Linux 4.9.x?

I've scoured the internet for Linux IrDA support and found very little recent information. I'd like to use very basic 3/16th pulse encoding on a i.MX6ull based SoM. Using low level register access (...
0
votes
0answers
23 views

Software to replay a serial signal on a serial port (with accurate timing)?

I was looking for this, but seemingly I cannot find anything relevant - so maybe someone can point out possibilities or software that can do this? What I need, is to play back, from a file, a signal ...
1
vote
1answer
38 views

How to map /dev/ttyUSB0 (usbserial CP210x) to a COM port in wine?

I'm running a Windows application in wine. The app can only see COM ports 1-4. My system has the following usb-serial device: # lsmod | grep cp210x cp210x 36864 0 # ls /dev/...
0
votes
0answers
20 views

Software/Way to interpret UART data coming in from toggling GPIO

I'm having one GPIO on my SBC (in this case: Raspberry Pi, but it shouldn't matter), which is attached to a peripheral device dumping log output on this pin. Format is UART (8N1), baudrate ...
0
votes
1answer
30 views

Serial console messes up occationally

Occationally my serial console messes up severely like this: Typing doesn't work there are all anymore. Though the machine still functions fine. So if I reboot it (as shown in the screenshot. PC ...
1
vote
1answer
43 views

STM3210 USB to serial adapter not showing up in /dev/ttyUSB

I found a vinyl cutter on Ebay, and purchased it. Then I stumbled upon this video: http://www.youtube.com/watch?v=3tZXsUGEJ-E which demonstrates that it is possible to use this type of device on ...
0
votes
1answer
54 views

Send binary file to ttyUSB0 serially in linux

I have a binary file(obtained from assembly code). I need to transfer this file to an fpga serially via ttyUSB0. I read in some posts that using cat and echo data can be transferred to ttyS0. echo -...
0
votes
1answer
76 views

socat - multiple connection attempts fail to pass through serial

I'm using socat to route serial input over a network to allow me to control an Arduino device over a virtual COM port setup. My command to start socat is: socat /dev/serial0,b500000,raw,echo=0 TCP-...
0
votes
1answer
64 views

/etc/inittab: auto login on ttyS0

in my /etc/inittab, I have this line: T0:2345:respawn:/sbin/getty -L ttyS0 115200 vt100 which gives me getty on serial console where I can log in. How can I specify that instead getty, I get ...
0
votes
1answer
31 views

Multiport serial adapter: none work even with driver loaded

I have bought this serial adapter On linux debian is recognized lspci -k 02:00.0 Serial controller: Device 1c00:3253 (rev 10) Subsystem: Device 1c00:3253 Kernel driver in use: serial ...
0
votes
1answer
79 views

Why I'm not getting any output differential when toggling my RTS pin on my RS232 port?

I'm trying to turn on/off a output or switch a relay etc by controlling the RTS or DTR pin of my RS232 signal. I've created a script in C that switches my DTR or RTS flag on/off but I'm not getting ...

15 30 50 per page
1 2 3 4 5 27
怎么样进入赌单双软件 手机棋牌输了几百万 怎么购买手机赌博软件 我爱彩票邀请码是多少 我想查查彩票开奖结果 快钱彩票官网 快乐棋牌游戏 手机版彩票过滤工具 怎么下载波克棋牌 快乐12任5遗漏数据